Electrician referrals for Phoenix & nearby townsCall: (602) 584-7286
(602) 584-7286

Why a breaker keeps tripping, and when to call

electricianphoenixaz.net

A circuit breaker trips on purpose: it cuts power when a circuit carries too much current or leaks current where it should not. This guide covers the common causes in Phoenix-area homes, the few checks that are safe for an owner, and the point where you stop and call.

Need an electrician now?
Call now to be connected with a local electrician in Phoenix.
(602) 584-7286

A circuit breaker trips on purpose: it cuts power when a circuit carries too much current or leaks current where it should not. This guide covers the common causes in Phoenix-area homes, the few checks that are safe for an owner, and the point where you stop and call.

What a tripping breaker is telling you

A breaker is a safety device, not a nuisance. It watches the current on one circuit and opens the switch when that current stays too high or spikes suddenly. One trip after you plugged in a space heater and a vacuum together is ordinary. A breaker that trips again and again, or one that will not stay reset, means something on that circuit needs attention.

Electrician Phoenix is a free referral service that connects callers with independent local electricians in the Phoenix area. It is not an electrical contractor, and this guide is general information, not a diagnosis of your panel.

Safety first

If you see sparks, smell burning, notice smoke, or find a breaker, outlet or panel cover that is hot to the touch, leave the house and call 911 before anything else. The City of Mesa Fire and Medical Department says that if you see flames or smell smoke you should leave immediately and dial 9-1-1. ESFI lists a burning or hot-insulation odor, hot or discolored switch plates and outlets, and sparks as signs of a serious wiring problem. Our guide on what to do about a burning smell walks through that situation in more detail.

Never remove the panel cover, probe the breakers or tighten anything inside the box yourself. Panel work belongs to a local electrician who holds an ROC license.

The three kinds of trip

Not every trip has the same cause, and the pattern helps an electrician narrow it down.

  • Overload. Too many devices draw from one circuit. The breaker may take a few minutes to trip under a steady heavy load, and it usually resets once you unplug something.
  • Short circuit. A hot wire touches a neutral or ground wire, or a damaged appliance cord does. The breaker trips almost instantly, often with a pop, and may trip again the moment you reset it.
  • Ground fault. Current leaks to ground, often through water. GFCI and AFCI devices exist to catch these, and they can trip without the main breaker moving at all.

Write down what you were running, how long the circuit held and whether you heard anything. That short note saves diagnostic time when an electrician arrives.

Call now to be connected with a local electrician in Phoenix.
(602) 584-7286

Common causes in Phoenix-area homes

Valley homes add their own patterns on top of the general ones.

Air conditioning on a shared circuit

A cooling system pulls a large surge when the compressor starts. If an AC unit, a mini-split or a window unit shares a circuit with other loads, or the unit is aging and drawing more than it used to, the breaker can trip on startup in the hottest part of the day. Equipment of that size normally needs its own circuit, which is the idea behind dedicated circuits and AC wiring.

Small service in an older neighborhood

Many 1940s through 1960s homes were wired when a household owned a fraction of today's electronics and appliances. Add a modern kitchen, a hot tub or a second refrigerator in the garage and the original capacity runs short. When several circuits trip in turn, the issue may be the size of the service rather than any single branch. A service upgrade is the usual answer.

Pools, spas and outdoor circuits

Pool pumps, heaters and spa equipment live in a wet, sun-baked setting. Moisture in a connection or a worn pump motor often shows up as a GFCI trip. Repeated trips on pool or backyard equipment deserve a proper look from someone who handles pool and spa electrical work, not a repeated reset.

Monsoon moisture and surges

Storm season brings wet outdoor boxes, power flickers and, after outages, brief spikes when service returns. APS advises unplugging unneeded equipment after power returns to avoid electrical spikes. A trip that begins right after a storm may point to water in an outdoor outlet or a damaged device.

A worn breaker or a loose connection

Breakers wear out, and a connection that has loosened over years of heat cycling can warm up and cause nuisance trips. Some older panel brands, including Federal Pacific Stab-Lok and Zinsco, have a poor reputation for breakers that fail to trip when they should, which is a reason to have an old panel looked at even when it seems to work. That is the territory of circuit breaker repair and, for deeper trouble, electrical panel repair.

Checks an owner can safely make

You can do a few things without opening anything.

  1. Note which breaker tripped and what is on that circuit.
  2. Unplug everything on the circuit, then reset the breaker firmly to off and back to on.
  3. If it holds, plug devices back in one at a time and see which one brings the trip back. A device that trips the breaker alone should be taken out of service.
  4. Press the test and reset buttons on any GFCI outlet in the area, including the garage, kitchen, bathrooms and exterior. A tripped GFCI is often what killed the outlets you are chasing.
  5. Look at cords and plugs for scorching, cracking or a melted look.

If the breaker trips with nothing plugged in, if it feels warm, or if you hear buzzing or crackling from the panel, stop. The fault is in the wiring or the breaker, and it is not an owner project.

What not to do

Do not swap in a larger breaker to stop the tripping. The wire in the wall was sized for the original breaker, and a bigger one lets the wire overheat before the breaker reacts. Do not hold a breaker in the on position, tape it or bypass it. Do not use an extension cord as a permanent fix for a circuit that cannot handle the load.

When to call a local electrician

Call when a breaker trips repeatedly, when it trips immediately on reset, when you cannot tell what is on the circuit, when lights dim as the air conditioner starts, or when the panel is warm, noisy or discolored. Many electricians take after-hours calls, though availability varies. If the problem keeps a medical device or your cooling off in extreme heat, say so on the phone.

The usual first step is electrical troubleshooting: tracing the circuit, testing the breaker and checking connections. Published Phoenix guides put electrician labor at roughly $40 to $100 per hour on HomeGuide and $50 to $150 per hour on Angi, and HomeGuide lists an average call-out fee of about $75. Those are published ranges rather than quotes. The electrician cost guide explains what moves a price up or down.

How an electrician approaches the problem

A good diagnosis starts with questions: when does it trip, what was running, has anything changed lately. Then the electrician isolates the circuit, checks what is connected to it, tests the breaker under load and inspects terminations at the outlets and in the panel. Expect a clear explanation of the finding before any parts are replaced. If the cause is a worn breaker, replacement is a modest job; if it is overloaded wiring, the fix is new circuits or a larger service, and that deserves a written scope.

Before any work starts

Check the contractor's ROC number on roc.az.gov before work begins. The ROC uses class R-11 for residential electrical work. Replacing a breaker or panel in Phoenix can involve a permit, and the permit office is the City of Phoenix Planning and Development Department; see electrical permits in the Phoenix area for how that works, and hiring an electrician in Arizona for the license check step by step. If you live outside the city, find your town on the service areas page.

The short version

An occasional trip under a heavy load is normal. A breaker that keeps tripping, will not reset or comes with heat, smell or noise is a fault. Take safe steps, leave the panel closed and call. Related reading: summer heat and your home's electrical system.

Frequently asked questions

Why does my breaker trip when the AC starts?
A compressor draws a large surge at startup. A shared circuit, an aging unit or a loose connection can push the load past the breaker's limit. An electrician can check whether the unit needs its own circuit.
Is it safe to keep resetting a breaker that trips?
No. Repeated resets on a breaker that keeps tripping can mean a short circuit or a failing breaker. Reset it once after unplugging devices, and call an electrician if it trips again.
Can I put in a bigger breaker?
No. The wire in the wall was sized for the original breaker. A larger one can let the wire overheat before the breaker trips, which creates a fire hazard.
What if the breaker is hot or the panel buzzes?
Treat it as an emergency. Leave the house and call 911 if you see sparks, smoke or smell burning, then have an electrician inspect the panel before it is used again.
Who handles breaker repairs?
A local electrician who holds an ROC license. Call the number on this page to be connected, then check the ROC number on roc.az.gov before work starts.
Call now to be connected with a local electrician in Phoenix.
(602) 584-7286

Last updated:

☎ Call (602) 584-7286